SIGN UP TO BECOME A VIP!

DIY Lined Roman Shades

Hey friends!

I get asked about my roman shades all the time.  I decided it was time to change mine out, and I thought this would be a great time to attempt a tutorial.  You should be warned…. I feel like writing this tutorial is harder than making the darn shades… Just saying 😉

So, here we go.  If you can sew a straight line, you can make these. Promise!

You need to measure your window.  You can make these wider than your window, but for mine I prefer to mount them on the insides of the window.  Measure your window width and write it down.

Fabric…

I decided to use good old drop cloth for mine!

Cheap and easy, and I will be stenciling it in a later step.

Your fabric needs to be cut 1″ wider than your window width, and 8″ longer than your window length.

You will also need your liner fabric.  You can find drapery liner at any craft store.  Your liner needs to be cut the same length as your other fabric, but 1″ smaller than your window width.

Lay your fabrics out.  Fold each fabric up 3″ from the bottom to create a hem on each piece. Sew a straight line on each piece to hold this hem in place.

Now you will attach both pieces together like a giant pillowcase with the top and bottom open.  Place the good sides of both fabric pieces together a do a straight stitch up both of the long sides.

Now for the dowels…

I use dowel rods to keep my shades folding clean and pretty.  You can buy these at any craft store up to 36″ and Lowe’s sells them up to 48″.  I use 1/4″ diameter dowels.  Cut each dowel about 4″ less than the width of your window.  My window measures 30″, so my dowels are cut at 26″.  I just used a really sharp pair of scissors to cut mine.

I use Aleene’s Tacky Glue to attach the dowels to the fabric.  This is what the bottle looks like.

You’re going to be attaching your dowels on the inside of your fabric piece, not your liner.  Lay your fabric out flat on the ground.

Measure 9″ up from the bottom of your hem.  Add a line of glue to attach your first dowel like this…

Now you will attach your other dowels.  Measure 7″ up and glue down your next one.  You will glue the dowels every 7″ until you get to the top of your fabric.  It should look like this…

After your glue dries you will turn your fabric piece inside out.  This can be a little tricky with the dowels, but just do it slowly and it’s easy. The front fabric piece will be just a bit wider than your liner fabric on the sides.  Now it’s time to attach the rings.  You can buy plastic rings at any craft store in the drapery or fabric section.

This is the tedious part because you have to sew these on with a needle and thread.  It’s easy though!  Starting with your bottom dowel, sew on three rings.  You will sew one one each side and one in the middle.  Put your thread in through the liner, or backside first. You will actually go through the front of the fabric also.  Your thread will show just a bit on the front, so make sure to use a thread color that blends with your shade fabric.  You won’t notice it at all when the shade is down.

Also, make sure you sew your thread around the dowel.

There will be three rings on every other dowel until your reach your top dowel.

Next, you need to attach your shade to a 1×2.  These are super cheap. They can be easily cut with a cheap hand saw, or Lowe’s can cut them for you also. It needs to be 1/4″ smaller than the width of your window.  Attach 3 eye hooks to one side of the wood like this.

Then, measure your fabric from the bottom hem.  Draw a line on the back liner fabric at the length of your window.  Attach the fabric to the wood at this line using a staple gun.

Cut any extra fabric off after you staple it.

Your final step before hanging it up will be attaching drapery cord.  This can also be purchased at any craft store.  Tie the cord to the bottom right ring and then string it through the rings above and through the eye hooks like this…

After going through your third eye hook cut the string at about 3-4′ and leave it to the side.

Now do the same thing starting with your middle bottom ring like this…

Finally, do the same thing starting with your bottom left ring.  You will then have three long strings out to the side of your shade.  I use a fan pull for my cord pull.  I found mine at Lowe’s.  Just run your three cord pieces through the pull and tie a knot like this…

Pull the knot into the pull like this…

Almost done I promise!

To hang your shades you will use an L bracket like this.  Again, found mine at Lowe’s.  Measure where your 1×2 will sit and attach them to your window like this…

Now you will put your shade up on your 1×2 and screw a wood screw up through the bottom of the L bracket like this to hold it in place.

That’s it!  I know it sounds like 4385734598743095 steps, but I promise it is super easy!  It’s just really hard to put the steps into good words, so hopefully the pictures will help with that.  If you have any questions just ask!  You can also ask me on Facebook for a quick answer.  Want to see it all finished??

I used plastic cord cleats like this (Lowe’s) to hold my cord…

Hope you like them!  These babies will last too!  I have had my other ones hanging for almost 3 years.  I open and close them every day and have never had a problem with them.

If you like them, please Pin it, Stumble it, and Share it below! I would appreciate it!! 🙂

Have a great weekend!

~Whitney

69 Comments

  1. Susan on April 25, 2020 at 8:12 am

    If you glue the dowel to the front fabric …. doesn’t the glue show through the front of your shade

  2. Vickie on October 5, 2018 at 7:13 am

    I am adding a padded insert lining for added warmth/insulation.
    Do you think I should attach the dowel to the front fabric or the padded fabric. If the padded would you glue the dowel to the front or back of the lining?

  3. Patty on September 15, 2018 at 6:24 pm

    I don’t see where you see the two pieces together at the hem. Does that happen? I saw where you do each hem, but not when or if you see them together. Thanks

    • Patty on September 15, 2018 at 6:27 pm

      *Not see – sew them together

  4. Eleanor on March 5, 2013 at 5:41 pm

    This is by far THE BEST tutorial on making a Roman shade. I am definitely going to do this now. Thanks so much!

  5. donna stropes on February 28, 2013 at 9:19 pm

    thank you so much for this…….. i have some I bought from ?? but they keep
    coming apart at bottom, then cannot lift up…..u just gave me solution to fix them and maybe make some drop cloth ones for our guest house
    thank you

  6. Kelly on February 24, 2013 at 11:45 am

    We made these shades this weekend and the directions didn’t account for a seem allowance. We cut both fabric pieces as directed and the shades came out smaller than the window. The patterned fabric used should have been cut 3″ larger than the window to give a 1/2″ seem allowance and give an extra inch on each side of the liner fabric as the pictures appear. Other than that, these directions have been pretty straight forward.

    • Aidan Cusson on March 15, 2013 at 7:43 pm

      I just found out this too. How does yours look? I haven’t mounted mine yet

  7. Gail on February 8, 2013 at 10:31 pm

    I would love to make this for a door with a glass panel – it’d be perfect! But I’d prefer not to drill into the door. I was thinking about screwing heavy duty magnets into the 1×2. Do you think that could hold the weight of the blind and it still lay nicely? Thanks – love your site!

Leave a Comment