SIGN UP TO BECOME A VIP!

Wine Rack – DIY

Hey guys!

We love a quick and cheap project and this Wind Rack – DIY might be a Shanty Fave!

Shanty 2 Chic Wine Rack 4

Today we will be showing you all how to make this simple rustic chic wine rack for under $15.  Can’t beat that!

Here are the supplies you will need for this project…

1 – 2×6 cut at 38″

5 – 2×4 cut at 10″

10 – 5/16 x 4 1/2″ hex bolts (we found ours on the hardware aisle for $.38 a piece)

10 – 2 1/2″ wood screws

wood glue

finishing supplies

Now let’s get started!

We used our miter saw to make all the cuts.  This saw makes it simple and quick!  We had them done in no time!

Ryobi Compound Miter Saw

Before attaching all of our pieces, we like to sand all of our corners and edges down a bit with my corner cat sander. We love the look it gives the finished piece!  We use it all the time and it’s perfect for this job.

Ryobi Corner Cat Sander

This is what the edges look like after we finished sanding.

sanded edge of wood

We started by marking our 2×6 board.  We lined up our 2×4 piece every 6″ and marked lines on the bottom and top of the 2×4.  We did this to both sides of the 2×6 board.

mark line on wood

Before attaching our 2×4’s to our 2×6, we put 2 holes in the top and front of each 10″ piece.  You want them really close to the front.  Ours are about 1/4″ from the edge.

Picture 7

We used our cordless drill for this part!  This is hands down our favorite drill we have ever used!  It has so many cool features that set it apart from others, and it’s lightweight.

Next, we added a line of Gorilla wood glue onto our 2×4 pieces and clamped them to the 2×6 where we made our marks. Easy!

clamp

We used our drill to pre-drill 2 small holes where each 2×4 piece would sit.

Ryobi Drill

Now we used our drill to insert our wood screws through those holes.  This is what the back of the 2×6 looks like where each 2×4 sits.

Wood Screws

After we had all of our boards attached, we gave the whole piece a coat of our favorite…

Rust-Oleum-Dark-Walnut

We use Dark Walnut Stain.

After it dried we went back over the edges and corners again with our Corner Cat to give it a worn finish.  Love it!

We decided to ‘shanty’ it up a bit by adding a small label on the front of each board using chalkboard spray paint.  We just taped the area off with blue tape and spray painted the chalkboard paint on.  Totally optional!

Our final step was adding our hex screws.  Just insert 1 into each of the holes and you are set!

Make sure to use anchors on the wall if you can’t attach yours to a stud.

Here is ours all finished up!

Shanty 2 Chic Wine Rack 5

Shanty 2 Chic Wine Rack 3

Shanty 2 Chic Wine Rack 1

Shanty 2 Chic Wine Rack 2

Shanty 2 Chic Wine Rack 4

Hope you love it!  Ash and I had so much fun working on this one together!

Thanks so much for stopping by!  We hope you guys have an awesome weekend!  Make sure to share your Shanty inspired creations with us over on our Facebook page!  We love seeing and sharing them!

29 Comments

  1. Daisy on May 11, 2018 at 12:39 pm

    this is great my dad owns a pub and this will be perfect as we have a lot of wine drinkers 👍🏻😂😝

  2. puspendu on February 15, 2018 at 12:28 am

    I have Some Concept Problem But After Reading Your Post My concept Got Crystal Clear. Thanks For Sharing The post”Love What You Do And Do What You Love! ” .. It was full of note worthy . I like reading Post On your website because it goes Excellence And With a charismatic.

  3. Md on January 10, 2018 at 6:45 am

    This is really nice post. This post has really impress me through its quality writing. In this article i watch some new writing style which is really nice. So thanks for sharing such a awesome post.

  4. Randy on February 22, 2016 at 8:25 pm

    Looks very nice…do you have plans without all of the pictures? I know what my Ryobi tools look like 🙂

  5. Brian on August 31, 2015 at 6:52 pm

    Finished this a couple weeks ago… Wanted to fill it up with wine
    before I posted a pic. I made one for a friend also. Thanks for the
    plans!

  6. Anne Curwen on August 3, 2015 at 7:13 am

    One of my favorite projects! Thanks for the idea!!

Leave a Comment