SIGN UP TO BECOME A VIP!

DIY Farmhouse Bathroom Vanity

Learn how to build this DIY Farmhouse Bathroom Vanity with free plans by Shanty2Chic! This is an easy build that only requires a few tools!

This room has been in the works longer than I care to admit, but I finally got around to finishing it and I LOVE THE RESULTS!  Check out my oldest son’s new bathroom and his new farmhouse bathroom vanity!

As always, I will share the entire build with you here, and you can download and print our free plans by clicking HERE!

Now to build the vanity!  This really isn’t a difficult build…. If you can get the angle cuts down, the rest is very basic.

DIY Farmhouse Bathroom Vanity

I started by building two sides.  These are constructed out of 3/4″ Purebond Plywood.  This type of plywood is sold in big 4’x8′ sheets, and we have the guys at Home Depot rip it down into smaller boards to fit in the car.  Then, we cut those boards to exact size using our miter saws or table saws.  I cut mine to size and then added 3/4″ pocket holes down the sides and top.  The top pocket holes will be used attach the wood countertop.  If you are doing just a drop in sink top/countertop with no wood below it, you can skip those pocket holes.

Purebond for vanity side

Next, I cut and attached the legs.  These are made of 2×3 boards.  Rather than just purchasing 2×3, we like to purchase 2×4 and cut the rounded edges off to make it a very square 2×3.  You do this by running each end through a table saw.  I love the look!

Attaching pocket hole screws
pocket holes for DIY vanity

After attaching both legs, I added the X trim pieces.  I used 1/2″ craft boards for this part.  They can usually be found by the 1x pine boards at the hardware store.  I used pine for this part as well.  I found the easiest way to get these angles was by laying the board down on the side of the vanity and drawing where my cuts should go.

I attached each board using my Ryobi 18v brad nailer with 3/4″ nails and wood glue beneath each board.

nail down trim on vanity
Build side of DIY vanity

After building both sides, I attached them with the front and back frame pieces.  These will also be attached using 3/4″ pocket holes and 1.25″ pocket hole screws.

adding front frame of bathroom vanity

The base of the vanity is also Purebond.  I added 3/4″ pocket holes around the base of the whole thing before attaching to the inside of the cabinet.

pocket holes for base

Here she is ready for her door!

How to build a bathroom vanity

I cut the door pieces to size on this part, and then added 3/4″ pocket holes to both ends of each shorter board.

wood for door on vanity

Then, I made a frame with those 4 boards using 1.25″ pocket hole screws.

building the door frame

The backing is 1/4″ Purebond plywood.  I attached this using wood glue and 3/4″ staples with my Ryobi 18g stapler.

nail inside of door

Next, I added the X detail using the same method I did on the sides by marking where my cuts would be.

building door of bathroom vanity
door of bathroom vanity

 Now for the top!  Again, yours may just be a drop in top similar to what I used on my last vanity.  If so, you won’t need the wood top I am about to show you.  I built mine by starting with a piece of 3/4″ Purebond plywood cut the size of the countertop I wanted minus 1.25″ all around.

Then, I planked the top with 1/2″x 4″ oak boards.  I used wood glue and nails to hold these in place.

glue down oak boards
oak boards for vanity top

I trimmed the outside of the countertop with 1×2 oak boards.

wood top for vanity

Next, I laid my sink template on top and used my Ryobi jigsaw to cut along the line for the sink.

cutting wood countertop

To do this, I started by making a pilot hole with my drill.  This will allow me to drop my jigsaw blade into it to start my cut.

Drill pilot hole at corner

This is the blade I used…

jigsaw blade

Then, I just cut around the line.

Cut along line with jig saw

Then, I made sure it fit!

Fit sink in vanity

I stained the countertop with Varathane Dark Walnut stain.

Varathane-Dark-Walnut

After it dried, I added two coats of Varathane Triple Thick Poly.

Varathane Triple Thick

This says GLOSS BUT I used Satin!

I painted the entire cabinet with Varathane Chalked paint in Charcoal and then lightly sanded my edges to distress it a bit.  I also added one coat of Triple Thick to the cabinet base.

Paint for Bathroom Vanity

These are the hinges I used to attach the door.  They are from Home Depot.

Hinges for Bathroom Vanity

And this is what I used for the door latch, also from Depot!

Sideboard Hardware from Home Depot

Here it is all finished up!

Free Bathroom Vanity Plans DIY

How pretty is the faucet guys?  I worked with Moen on the finish out of this space.  The faucet is a Weymouth Oil Rubbed Bronze one-handle bathroom faucet.

I’ve also had a ton of questions about the tank lever.  It is also a Moen Weymouth tank lever in oil rubbed bronze.

And the Weymouth paper holder has become a game changer in my house.  This design is amazing!  It makes changing the toilet paper roll so much easier… It’s the little things 😉

Shanty2Chic DIY Bathroom Vanity Plans
Free Bathroom Vanity Plans DIY
DIY Bathroom Vanity by Shanty2Chic

I worked with one of our favorite brands for this part.  I found all of the tile for the bathroom at The Tile Shop!  Below I will link to each tile so you can find it on their site.

Pillowed Marble Subway Tile

Marble Trim Pieces

Adoni Black Slate Floor TileParagraph

And now for the rest of the goodies!  This vanity is designed to fit a drop-in sink.  I found mine on Wayfair. I wanted something that covered most of the countertop to keep my son from getting too much water on the wood.  HERE is the drop-in sink I found.

The amazing mirror and light are also from Wayfair.

The shower faucet is also from the Weymouth collection.

Wall Mirror

LOVE the light and it’s price tag!

Progress Lighting Archie Light

I also found his shower curtain and curtain rod on Wayfair!

Whew.  That was a mouthful. 🙂  Hope you like it as much as we do!

Let me know if you have any questions at all!

36 Comments

  1. VelvetFields on August 5, 2021 at 1:57 am

    Awesome ways, Dude.
    I really like the point and best of all time.

  2. GoDigi Shop on July 15, 2021 at 12:20 am

    Very Informative and useful blog. I had a Great time reading this, thank you for sharing this with us!

  3. mina on May 16, 2021 at 5:38 am

    Blackout curtains decorative and blackout window treatments have always been popular decorative items. There is a wide array of styles, materials, and colors to enhance the elegance of any home.

  4. Vape Road on April 19, 2021 at 12:10 am

    Good job! Personally i really appreciate of your work. Good luck!

  5. William M. Dozier on April 2, 2021 at 5:22 am

    keep up the good work. Well done.

  6. Jessica Steve on January 25, 2021 at 12:17 am

    Perfect post. I like a post you are the most valuable information and This is really great work.

  7. Carolyn Gill on January 16, 2021 at 10:06 pm

    I like how you make a bathroom vanity yourself. Inspiring

  8. Debbie on January 9, 2021 at 6:39 pm

    can’t wait to try it

  9. Umar on January 9, 2021 at 11:04 am

    Amazing bathroom I love your natural Stone tiles

  10. Best Shot Gun on December 3, 2020 at 5:19 am

    I Have a Question that In Recording the Video Voice Recording Issue Comes. Then We Use Separate Microphones Like Best Shot Gun Mic So Here are Some Blogs Visit Please:

  11. Kitchenvio.com on December 3, 2020 at 5:15 am

    Would you want A Kitchen Related Site If Yes then Visit My Name.

  12. Best Dash Cam on December 3, 2020 at 5:11 am

    Thanks For the Information I Love your Blog That’s have a lot of Beneficial Information. On the Road the Traffic and Drivers are on Very Speedy way. So, I have a site like a Best Dash Cameras. Visit the Site and Tell Me How This is Thanks :>

Leave a Comment