This DIY Engineer Print Frame is probably one of the easiest projects I have done and it makes such a huge statement in a room! It also only cost me about $20 to make – HECK YAH!
I made this as part of the “baseball” theme room that my son asked for. He LOVES baseball and what teenage boy wouldn’t love a giant 3’x4′ picture of themselves doing what they love?
Here are the supplies you will need:
1 scrap piece of 1/4″ plywood (at least 36″x48″ in size)
1 engineer print
2 – 1×4 common (or pine) boards @8ft. long
2 – 1×2 pine boards @8ft. long (I used premium pine)
Kreg Jig and pocket screws
Nailer/Stapler (hammer and finish nails work too)
Stain or paint for the finish
3″ Screws to hang
I started with a picture that I took, myself. Then, I uploaded it to Staples and ordered a 36″x48″ engineer print. You can see where I ordered it HERE. It was ready the same day and it was only about $8!
Next, I found a piece of scrap 1/4″ plywood. It just needs to be long enough and wide enough to fit the entire picture.
Next, I trimmed the white border off of the engineer print, with scissors, and cut the plywood to size. I used 1×4 pine boards for the frame, so make sure that the plywood is long enough for the frame pieces too.
Once the plywood was cut to fit, I used double-sided tape to attach the picture to the plywood. The 1×4 frame will hold the picture on as well, so all you need to do is have it taped for now.
Next, I cut the top and bottom 1×4 boards for the frame. Measure and cut to fit your picture. I cut mine at 48″. Then, measure to cut the two side pieces. Mine were 29″. Then, I drilled 3/4″ pocket holes into the side 1×4 boards, on both ends. You can find the Kreg Jig K5 jig that we use on Amazon, HERE. You can also check out our How to Use a Kreg Jig video tutorial HERE.
I assembled the frame with 1 1/4″ pocket hole screws. Here is how the frame will look , assembled, from the back side. Notice where the pocket holes are.
Now to attach the 1×2 border. Don’t attach the frame to the picture yet, you will want to put your finish on the frame before, so you don’t mess the picture up. Just hold the frame up to the picture so you know where to attach the 1×2 pieces. The top and bottom 1×2 pieces will be the same length as the top and bottom 1×4 pieces. Then measure and cut the side pieces to fit.
Apply wood glue to the top edge of the 1×4 pieces
and use 1 1/4″ brad nails to attach the 1×2 pieces. Notice the 1×2 piece on the top is flush with the outside edges of the frame, the back of the 1×2 will be flush with the back of the plywood. You can use a hammer and finish nails here if you don’t have a nailer.
Here the frame is ready for the finish!
I applied one coat of Varathane Dark Walnut stain, to the entire piece, with a clean cloth. This is our favorite stain because it achieves color in only one coat! Wait about 5-minutes for the stain to soak in, then wipe the stain with a clean cloth to blend the stain evenly. It should dry, to the touch, in about an hour.
When the stain dries, just attach the plywood (with the picture) to the back of the frame. I used 3/4″ staples and my Ryobi Airstrike stapler. You an use a staple gun here or finish nails and a hammer.
That was it!
To hang it, I located the studs on the wall and attached the frame to the studs, through the front of the frame. This will leave holes in the frame, so just fill them with wood filler, let the filler dry and dab a little stain over the wood filler 🙂
I had so much fun making this for my son and he LOVES it too! Win, win! I’ll share the floating desk plans soon but you can check out the rest of his room in the images below! Everything is DIY, so just click the links below the pictures for the how-to’s!
Thanks so much for stopping by!
Board and Batten Hat Rack