SIGN UP TO BECOME A VIP!

DIY Media Storage Dresser

This is a giant piece with 6 glorious giant drawers! And, it is part of a 6-piece unit that I am so excited about building for my master bedroom!

DIY-Media-Dresser

It’s one of the largest single pieces of furniture that I have built but that does NOT mean it is difficult. It’s still easy to build it’s just really…BIG 😉

me-with-dresser

MY LATEST VIDEOS

I had my son take a pic of me with it, before I installed the drawers, to share on our Instagram!

As always, we have the FREE plans for you! You can click HERE or the image below to print.

click-for-dresser-plans

And, you can follow along with my build below!

lumber-loaded-in-car

Here is the before 😉 I think the worst party of a build is unloading the lumber! I used our favorite Purebond plywood for all of the plywood in this piece. Purebond is our go-to plywood because it is a formaldehyde-free product. This means Whitney and I aren’t breathing in harmful chemicals while we build and when we bring the pieces in the house they won’t be harmful to the air our family is breathing. AND, it looks AMAZING when it is stained! You can learn more about the Purebond pledge we took HERE.

Kreg-Rip-Cut

I had the nice guys at Home Depot rip my Purebond boards so that I could fit them in my car then, I brought them home and cut them down more with my Kreg Rip Cut. This is a great tool to have in your shop. It is inexpensive and it doesn’t take up very much space. It just attaches to your circular saw and allows you to rip a straight cut with the guide! You can check it out in the Amazon box below.

rip-corners-of-plywood

I cut my side pieces first the, I used my jigsaw to cut out notches in the front corner of each piece.

side-with-corner-cut

So, each side piece will look like this.

shelves-with-pocket-holes

Then, I cut the shelf pieces and drilled 3/4″ pocket holes at each end of the boards.

attach-shelves

Next, I attached each shelf piece to one side piece with 1 1/4″ pocket screws and wood glue. *Make sure to keep the notch on the side piece in the correct place when attaching the shelves.*

attach-other-side

Then, I attached the second side piece the same way. *Again, make sure the notch in the side piece is in the right location when you attach the shelves.

attach-braces

Now, add the front and back braces to the bottom of the piece.

back-brace-flush-with-shelf

The back brace will be flush with the back of the bottom shelf.

frame-done

Attach the front trim piece after you notch the top corners to fit the sides of the dresser. I didn’t get a picture of this part but I used my jigsaw and cut a 3/4″x3/4″ notch out of each of the top corners of the 1×4 trim piece. You can see it in this picture at the bottom of the dresser.

face-frame

Build your face frame with 3/4″ pocket holes and 1 1/4″ pocket hole screws. Follow the diagram on the pdf plans for placement of the 1×2 pieces.

attach-face-frame-

Then, attach the face frame to the dresser with 1 1/4″ brad nails a wood glue. I used my 18 gauge brad nailer. You can also use a hammer and finishing nails here.

Now, attach the top horizontal braces and the back vertical braces. I don’t have a picture of this either. Attach them with 1 1/4″ pocket screws and wood glue.

attach-drawer-runner

Next, attach the drawer runners according to the placement on the plans. A clamp will help hold the board in place while you attach it with 1 1/4″ pocket screws and wood glue.

make-sure-runners-are-level

Use a level to make sure your drawers slide and fit easily.

drawer-runners-installed

Here are the runners installed.

attach-drawer-guides

Now, add the drawer guides.

attach-backing

Now, attach the plywood to the back of the dresser. I used my 18-volt stapler. I like to use staples when I attach 1/4″ plywood because it grabs the board better but you can definitely use finish or brad nails for this too. Make sure to use wood glue here too.

me-with-dresser

Now, we are at this point and ready for drawers!

measure-for-drawers

ALWAYS measure for the drawers before you cut them!!!! I can not stress this enough! Measure the length and the width then cut to fit. You will not be happy if you cut them all the same, build them and then try to slide them in – trust me…. I’ve learned the hard way many times!

building-drawers

After you have measured and cut your drawers (and drilled the 3/4″ pocket holes) you can build them with 1/4″ pocket screws and wood glue.

drawer

You’ll have six that look like this 😉

attach-back-to-drawer

Then, attach the 1/4″ plywood to the bottoms. Just like the back of the dresser, I used my stapler but finish or brad nails will do here too – and wood glue 😉

drawers-installed-without-fronts

Ahhhhh nothing like 6 drawers that fit nicely 🙂 Now for the faces!

attach-drawer-faces

Again, measure the drawer faces and cut to fit them! I attached them with wood glue and a few nails through the front of each drawer then I turned the drawer over and put lots of nails from the inside into the drawer face (less nail holes).

dresser-ready-to-stain

Tip here – number your drawers before you take them out to stain so you don’t have to play musical drawers when the stain is dry and they are ready to slide back in.

build-the-top

The final step is to build the top of the dresser. I used wood glue and my 18 gauge nailer.

attach-the-top

Then just attach it!

Time for stain!

Varathane-early-american

I used a favorite color, Early American by Varathane, to stain the entire piece.

If you watched our live Coffee Talk on Periscope, you probably saw that we love to stain with the lamb’s wool stain applicators (found at Home Depot). You can check that Periscope out on our Youtube channel now but make sure to follow us on Periscope so you can chat with us live! We are having so much fun with it! You can find us @shanty2chic. Click the box below to check out the lamb’s wool on Amazon.

Liberty-Hardware

Once the stain dried, the hubs and I brought this sucker in the house! We believe that the hardware on a piece really makes the piece special and this is no exception! I added another favorite – the Campaign Hardware from Liberty Hardware. You can check it out HERE from Home Depot. I used the same hardware on the nightstands that I built for our bedroom too and I LOVE it so much 🙂

That was it!

DIY-Dresser

DIY-Furniture

You can get the free plans to the bed in this picture HERE. And that bench/coffee table in front of the couch is also a DIY and only $20! You can get the plans HERE.

DIY-Media-Storage-Dresser

how-to-build-a-dresser

DIY-Media-Dresser

DIY-Dresser-With-Media-Storage

I can’t wait to build the rest of this set!

mediawall

It should look something like this – and I can’t wait 🙂 There will be bookshelves on either side of the dresser and the entire piece will have sliding bard doors that either cover the dresser and TV or cover the bookshelves!!

Media-Dresser-DIY

Until then, I have this really pretty dresser with tons of storage 😉

Thanks so much for stopping by!

~Ashley

More Posts Like This One

37 Comments

  1. Ashley on September 24, 2018 at 8:17 pm

    I love this piece and think it would be perfect for my living room, but on a much smaller scale: Only one shelf and four drawers and a little narrower. What’s the best way to alter/downsize your plans?

  2. Cole on August 5, 2018 at 8:49 am

    What kind of durabond plywood do you use? Sanded aspen or maple? Thanks.

  3. Frank on January 21, 2018 at 8:49 am

    Quick question here. On your tutorial you said you used 1/4″ ply for the bottoms of drawers, but in the pics and on the pdf plans you have the bottoms as 3/4. Just curious if there’s a reason for using the 1/4 over 3/4? Im actually customizing these plans to make a shorter dresser with baby changing table on top for the nursery.

  4. Redbeam100 on October 10, 2017 at 12:58 am

    Hello. Please help me. I am at the point of connecting the trim pieces. I drilled ¾ inch holes into the 1×2’s and used 1 ¼ inch kreg screws to connect them. I’ve cracked over 20 1×2’s. Am I doing something wrong? Please help…

    • Shanty2Chic on October 10, 2017 at 5:07 am

      Oh no!! It sounds like your pocket holes need to be deeper. Nothing should be cracking. Is it cracking when you attach with the screw?

      • Redbeam100 on October 10, 2017 at 6:10 am

        Yes! As soon I attach the screw (very carefully) the 1×2 cracks in the front and the screw shows. You mentioned my pocket holes, any suggestions on depth?

  5. Jeff on September 24, 2017 at 7:41 am

    I have built the sides,shelves and base and have noticed my sides have warped. I’m worried about continuing on if this can’t be fixed. Do you have any recommendations?

    I’ve read that wetting the concave sides can help but that is usually before building. Thanks!

  6. Kelly on February 4, 2017 at 5:37 pm

    Hi, you usually state what the piece cost you. I don’t see a cost. I’m deciding whether to buy a chest or build a chest. Love all you work.

  7. Janet Davis on September 15, 2016 at 7:54 pm

    Any chance of the barn doors coming soon? ????

  8. FloridaChris on August 22, 2016 at 1:32 pm

    Hello, I just finished making you King Size bed and will be making this dresser for the master bedroom as well. I have a random question. My girlfriend loves the color of the walls in your pictures. Could you tell me what brand and color it is?

  9. jhelfman on August 2, 2016 at 10:50 am

    Just want to say your projects are fabulous and are doable even by me.

  10. Fio Giana on March 12, 2016 at 7:14 am

    I’d like to use European drawer slides for the drawers, do you think the construction would change significantly? Other than the drawers being narrower to account for the needed gap?

  11. Joel Villanueva on March 9, 2016 at 5:31 pm

    about how much does this piece weigh?

  12. Allison Suarez on December 15, 2015 at 4:23 pm

    Is the rest of the set tutorial up yet?

  13. monee2000 on October 9, 2015 at 8:55 am

    When do you think the plans for the bookshelves will be ready? I have plenty of projects to keep me busy in the mean time, but I have the perfect place for this system and I love it!

    • Shanty2Chic on October 9, 2015 at 8:58 am

      Hopefully within the next couple of weeks! I am done building them just have to stain 😉

      • monee2000 on October 9, 2015 at 9:01 am

        Wheeeeeee! Great! Can’t wait to see them!

      • monee2000 on February 8, 2016 at 11:39 am

        Any chance the remaining pieces are coming soon?

        • Shanty2Chic on February 8, 2016 at 12:07 pm

          Bookshelves are coming this week!

          • monee2000 on February 8, 2016 at 12:14 pm

            Perfect – thanks so much!



  14. Sandor on August 12, 2015 at 6:43 pm

    I think there is an error in the plans, but I’m not sure: The total depth is 19 3/8 ” (which is the 18 5/8” side piece + the 3/4” front face frame). The depth of the shelf is 17 5/8”, and you add the 3/4” front panel, plus the 1/4 ” back. This adds up to 18 5/8”, which is a full 3/4 ” short. Am I missing something here? Ashley cautions to ALWAYS measure your drawer, so anyone who follows this advice should be okay. I’m just trying to work it out in my head.

    • Shanty2Chic on August 12, 2015 at 7:17 pm

      I’m seeing the shelf is 18 3/8″ deep. Would this make the difference?

      • Sandor on August 12, 2015 at 7:46 pm

        18 3/8″ would be right, but on the plans on the link it lists the depth as 17 5/8″.

  15. Steve Steiner on August 12, 2015 at 7:44 am

    How many DVDs do you think this will hold?

  16. Grant Laird on August 6, 2015 at 6:35 pm

    Good job!

  17. Rob B. on August 6, 2015 at 4:31 pm

    A lovely woman, power tools, a DIY project. What’s not to love? 🙂

  18. TerriL787 on August 6, 2015 at 9:25 am

    Absolutely beautiful….I love the hardware and the stain you used. Great job!!

  19. karl micheal on August 6, 2015 at 5:58 am

    Very nice. When I first looked at it, I was thinking…’How does she open the drawers?’ as the drawer pulls looked like the little content holder thingys (that is a woodworker term you know!! 😉 ) like you used to see on library card holders. Then I looked harder and saw they were some very nice pulls. This, my Dear, was a very nicely done and is a very nice looking ‘cabinet’!! Keep posting things for us!!

  20. Dona Stone on August 5, 2015 at 9:08 am

    So, you don’t use the metal drawer slides on your drawers? I always have such a hard time getting them lined up correctly.

    • Shanty2Chic on August 5, 2015 at 9:21 am

      Hey Dona,
      We didn’t on this piece and some other pieces 🙂 it kind of depends on the build!

      • Dona Stone on August 5, 2015 at 9:39 am

        It’s a beautiful piece.

Leave a Comment