This is a giant piece with 6 glorious giant drawers! And, it is part of a 6-piece unit that I am so excited about building for my master bedroom!
It’s one of the largest single pieces of furniture that I have built but that does NOT mean it is difficult. It’s still easy to build it’s just really…BIG 😉
I had my son take a pic of me with it, before I installed the drawers, to share on our Instagram!
As always, we have the FREE plans for you! You can click HERE or the image below to print.
And, you can follow along with my build below!
Here is the before 😉 I think the worst party of a build is unloading the lumber! I used our favorite Purebond plywood for all of the plywood in this piece. Purebond is our go-to plywood because it is a formaldehyde-free product. This means Whitney and I aren’t breathing in harmful chemicals while we build and when we bring the pieces in the house they won’t be harmful to the air our family is breathing. AND, it looks AMAZING when it is stained! You can learn more about the Purebond pledge we took HERE.
I had the nice guys at Home Depot rip my Purebond boards so that I could fit them in my car then, I brought them home and cut them down more with my Kreg Rip Cut. This is a great tool to have in your shop. It is inexpensive and it doesn’t take up very much space. It just attaches to your circular saw and allows you to rip a straight cut with the guide! You can check it out in the Amazon box below.
I cut my side pieces first the, I used my jigsaw to cut out notches in the front corner of each piece.
So, each side piece will look like this.
Then, I cut the shelf pieces and drilled 3/4″ pocket holes at each end of the boards.
Next, I attached each shelf piece to one side piece with 1 1/4″ pocket screws and wood glue. *Make sure to keep the notch on the side piece in the correct place when attaching the shelves.*
Then, I attached the second side piece the same way. *Again, make sure the notch in the side piece is in the right location when you attach the shelves.
Now, add the front and back braces to the bottom of the piece.
The back brace will be flush with the back of the bottom shelf.
Attach the front trim piece after you notch the top corners to fit the sides of the dresser. I didn’t get a picture of this part but I used my jigsaw and cut a 3/4″x3/4″ notch out of each of the top corners of the 1×4 trim piece. You can see it in this picture at the bottom of the dresser.
Build your face frame with 3/4″ pocket holes and 1 1/4″ pocket hole screws. Follow the diagram on the pdf plans for placement of the 1×2 pieces.
Then, attach the face frame to the dresser with 1 1/4″ brad nails a wood glue. I used my 18 gauge brad nailer. You can also use a hammer and finishing nails here.
Now, attach the top horizontal braces and the back vertical braces. I don’t have a picture of this either. Attach them with 1 1/4″ pocket screws and wood glue.
Next, attach the drawer runners according to the placement on the plans. A clamp will help hold the board in place while you attach it with 1 1/4″ pocket screws and wood glue.
Use a level to make sure your drawers slide and fit easily.
Here are the runners installed.
Now, add the drawer guides.
Now, attach the plywood to the back of the dresser. I used my 18-volt stapler. I like to use staples when I attach 1/4″ plywood because it grabs the board better but you can definitely use finish or brad nails for this too. Make sure to use wood glue here too.
Now, we are at this point and ready for drawers!
ALWAYS measure for the drawers before you cut them!!!! I can not stress this enough! Measure the length and the width then cut to fit. You will not be happy if you cut them all the same, build them and then try to slide them in – trust me…. I’ve learned the hard way many times!
After you have measured and cut your drawers (and drilled the 3/4″ pocket holes) you can build them with 1/4″ pocket screws and wood glue.
You’ll have six that look like this 😉
Then, attach the 1/4″ plywood to the bottoms. Just like the back of the dresser, I used my stapler but finish or brad nails will do here too – and wood glue 😉
Ahhhhh nothing like 6 drawers that fit nicely 🙂 Now for the faces!
Again, measure the drawer faces and cut to fit them! I attached them with wood glue and a few nails through the front of each drawer then I turned the drawer over and put lots of nails from the inside into the drawer face (less nail holes).
Tip here – number your drawers before you take them out to stain so you don’t have to play musical drawers when the stain is dry and they are ready to slide back in.
The final step is to build the top of the dresser. I used wood glue and my 18 gauge nailer.
Then just attach it!
Time for stain!
I used a favorite color, Early American by Varathane, to stain the entire piece.
If you watched our live Coffee Talk on Periscope, you probably saw that we love to stain with the lamb’s wool stain applicators (found at Home Depot). You can check that Periscope out on our Youtube channel now but make sure to follow us on Periscope so you can chat with us live! We are having so much fun with it! You can find us @shanty2chic. Click the box below to check out the lamb’s wool on Amazon.
Once the stain dried, the hubs and I brought this sucker in the house! We believe that the hardware on a piece really makes the piece special and this is no exception! I added another favorite – the Campaign Hardware from Liberty Hardware. You can check it out HERE from Home Depot. I used the same hardware on the nightstands that I built for our bedroom too and I LOVE it so much 🙂
That was it!
You can get the free plans to the bed in this picture HERE. And that bench/coffee table in front of the couch is also a DIY and only $20! You can get the plans HERE.
I can’t wait to build the rest of this set!
It should look something like this – and I can’t wait 🙂 There will be bookshelves on either side of the dresser and the entire piece will have sliding bard doors that either cover the dresser and TV or cover the bookshelves!!
Until then, I have this really pretty dresser with tons of storage 😉
Thanks so much for stopping by!
~Ashley
I love this piece and think it would be perfect for my living room, but on a much smaller scale: Only one shelf and four drawers and a little narrower. What’s the best way to alter/downsize your plans?
What kind of durabond plywood do you use? Sanded aspen or maple? Thanks.
Quick question here. On your tutorial you said you used 1/4″ ply for the bottoms of drawers, but in the pics and on the pdf plans you have the bottoms as 3/4. Just curious if there’s a reason for using the 1/4 over 3/4? Im actually customizing these plans to make a shorter dresser with baby changing table on top for the nursery.
Hello. Please help me. I am at the point of connecting the trim pieces. I drilled ¾ inch holes into the 1×2’s and used 1 ¼ inch kreg screws to connect them. I’ve cracked over 20 1×2’s. Am I doing something wrong? Please help…
Oh no!! It sounds like your pocket holes need to be deeper. Nothing should be cracking. Is it cracking when you attach with the screw?
Yes! As soon I attach the screw (very carefully) the 1×2 cracks in the front and the screw shows. You mentioned my pocket holes, any suggestions on depth?
I have built the sides,shelves and base and have noticed my sides have warped. I’m worried about continuing on if this can’t be fixed. Do you have any recommendations?
I’ve read that wetting the concave sides can help but that is usually before building. Thanks!