Hey there! I am so EXCITED about this project today! Chalkboards, key hooks and a mixture of galvanized hardware and stained wood are a few of my favorite things and this project has them all!
This cutie was SO easy! Don’t let the fancy cuts on the sides fool you! This is a beginner project from start to finish! I was able to make mine for under $20!
Lumber needed:
1 – 1×2 @ 8ft.
1 – 1×3 @ 4ft.
1 – 1×8 @ 4ft.
1 – 1×4 @ 4ft
1 – 2’x4′ Panel of Tempered Hardboard
*This is a great project to put scrap pieces to good use! If you don’t have scraps for the 4ft. boards, make sure to check the scrap boards at the hardware store for a great discount!
I started by cutting a piece of hardboard at 19″x24″. You won’t even need half of this panel so you can save it for another chalkboard project:) You can have your local hardware store cut this for you! I used my awesome Kreg Jig Rip Cut with my cordless circular saw. The Rip Cut is awesome for cutting down large panels like this!
I sprayed 2 coats of Spray Paint on the hardboard.
While waiting for the Chalkboard paint to dry, I got busy making cuts for the rest of the piece.
I used my 10″ Compound Miter saw to make my cuts but if you aren’t ready to make the purchase, you can purchase the handsaw below.
Cut list:
2 – 1×2 @ 24″
1 – 1×2 @ 19″
1 – 1×2 @ 16″
2 – 1×3 @ 17 3/4″
1 – 1×3 @ 16″
1 – 1×8 @ 16″
2 – 1×4 @ 10″ (for fancy cuts)
2 – 1×4 @ 6 3/4″ (for fancy cuts)
Here’s the part I promised would not be intimidating! Once you make your 1×4 cuts, these fancy cuts are a piece of cake! To make them even easier, I have provided printable templates below. Just print, cut and trace them on your 1×4 boards!
Once you trace the template, clamp the 1×4 down to a sturdy surface and cut away! I love my Ryobi cordless Jigsaw!
And, you don’t have to be exact on your Jigsaw because you can sand away the bad parts;) WE LOVE our Cordless Corner Cats! It is also an inexpensive tool and by far our favorite sanding tool. Notice it shares the Ryobi battery as well!
I used Gorilla Glue Wood Glue and nails for every joint! Attach the 2 – 1×3’s @ 17 3/4″. This will make the “shelf” part.
Now, glue and nail the “shelf” to the “A” pieces! I love using my cordless Brad Nailer for projects like this! This is also an inexpensive tool that will share the same battery as the other Ryobi cordless tools;)
Now, nail and glue the “B” pieces. This will form the dividers. This is the backside of the shelf so the fronts of the “B” pieces will be covered by the 1×3 on the shelf.
Front view of shelf. Now, set that aside.
Time to frame the chalkboard!
To frame the chalkboard, apply Liquid Nails to the back of the 1×2’s…
and place them around the chalkboard (flush with the outer edges). The top 1×2 is 16″ and the outside 1×2’s are 24″.
Now, attach the 16″ 1×3 to the bottom of the chalkboard (edges flush) with Liquid Nails. The 1×8 goes directly above that (also attach with Liquid Nails).
For the top trim, wood glue and nail the 19″ 1×2 to the top. The back edge will be flush with the back of the chalkboard leaving the front hanging over about 3/4″.
To attach the shelf, apply a thin amount of wood glue and nail from the back of the chalk board into the shelf and dividers. The bottom of the “A” pieces will be flush with the bottom of the 24″ 1×2’s.
Now for the finish!
Tape off right under the frame of the chalkboard before you stain. I thought it was easier to stain the piece after assembling (wood glue will not adhere to treated wood). The tape will protect the chalkboard finish.
I chose a classic favorite, Dark Walnut Stain to finish this cutie! Just apply one coat with a foam brush and wipe with a clean cloth after 5-10 minutes. Do not wipe the stain completely off, the wiping just helps to make the stain even.
Now for the detail!
I purchased to galvanized brackets and hooks to give this piece some character! Just use small wood screws to attach the brackets! That’s it! To hang it, I used a large sawtooth hanger and anchored a screw into our wall!
To get the distressed look on the stained wood, I sanded all of the edges with my Cordless Corner Cat!
What a great excuse for a “Collect-All”:) Again, this is totally a beginner project and the tools needed are very inexpensive and they share batteries! Go for it;)
If you love my DIY Chalkboard and Key Hooks, I would LOVE your pins and shares!
Thanks so much for stopping by and happy DIY!
~Ashley
I used a chalk pen to write on the chalkboard. It wipes away with a damp cloth. You can purchase the one that we love on Amazon below!
Can I get this already put toy???
I know this post is really old but what size brad nail did you use. The width of the wood doesn’t seem to match with size available for that gun?
acabe de terminar el mio , aun esta fresco
I love seeing what you guys do and have even implemented a few of your plans. This is the first one I have come across where I needed to double check the math and realized there are a few minor adjustments that are needed with the exact list of materials listed. All-in-all it’s a cool organizer and I will definitely be jumping onto another project here soon.
So far as the math goes here are a few things I noticed. First, the tempered board is going to be slightly less than 24″ exactly unless you buy a larger board and cut exact measurements of 19″ x 24″. That’s how all boards work. It’s a 2’x4′ board but it’s always slightly less. So when cutting your 1x2s they should not be cut until you know the exact measurements of your tempered board. Secondly, using that same train of thought with boards being slightly less than the name calls for the 1x3s are actually 3/4″x2-3/4″. The 2-3/4″ isn’t really that big of a deal unless you’re worried about the depth of the shelf part, but the 3/4″ part is detrimental when configuring the length of the cut for the shelving part. The instructions call for 17-3/4″. But if you use that exact measurement then adding a 3/4″ board on both sides will add up to what? 19-1/4″! The dimensions of the finished product is supposed to be (roughly) 24″ by 19″. So in essence you now have a shelf that is a quarter inch too wide to fit on the 19″ frame that you’ve built. Now you have wood over hanging. Also, the fancy cuts will need to be cut down as well to eliminate a gap between the frame and your shelf. If you get exactly what’s on the wood list it won’t work as the pictures portray.
We followed you plans for a wedding gift. We opted not to use the brackets though. Sorry the pic is sideways.
hi, I don’t really get the wood measurement. 1×2 @ 24″ , how long is this?
Hi,
A 1×2 is the board. Then cut it 24″ long 🙂
so 1×2 is thickness of the wood piece? And the length of the wood is 24″ how about the width?
1″ thick and 2″ wide board is a 1 x 2 board. It should be marked in the store.